10/31/2022 0 Comments Repetier server touchscreen mode exitThe reason I'm asking here, is because I also have a pi running octoprint on another machine, which I never have any problems reaching. I've searched for solutions but nothing seems to match my situation. But it will not load leaving me dead in the water unless I'm standing at the touchscreen controller. I'm using a static ip assigned in the router, and it's showing connected to the network every time in the router. The assisted leveling system reduces calibration to a single tap on the touch screen and the print nozzle can be swapped out in seconds, without the need for. interface templates created by Repetier-Server may only be used to create own brandings. Repetier-Server, it is forbidden to get around this by using plugins or custom programming. #REPETIER SERVER TOUCHSCREEN MODE EXIT PRO#It's like it's gone but the router shows it as connected. The touchscreen interface on the 3d printer may only be used in combination with the licensed Pro version of. On the touchscreen it's running just fine and I can control it there, but I can't do anything from my computer, or remotely if I needed to. Position the mouse pointer over the Zoom option, then select the Full-screen icon. Select the Settings and More option, represented by three horizontal dots in the upper-right corner of the browser window. But after it's been running a while, I get "this site can't be reached" every time. To use the menu option to enter full-screen mode: Open the Edge browser. Su ultimaker(Cmd) select beep led printer printer printer/head/0/slot/0 camera material printer printer/bed printer printer/head/0/slot/1 interface.http interface/http/auth nfc printer printer/head/0 system (Cmd) select printer printer/head/0/slot/0(Cmd) listangle = 70current_temperature = 27.7filament_size = 2.85flat_size = 0.3hardware_revision = 0hot_zone_size = 21.0hotend_cartridge_id = AA 0.4insert_type = tefloninteraction_required = 0is_enabled = 0is_present = 1is_primed = 1last_material_guid = 506c9f0d-e3aa-4bd4-b2d2-23e2425b1aa9manufacturer_id = Ultimakermaterial_extruded = 41175material_guid = 506c9f0d-e3aa-4bd4-b2d2-23e2425b1aa9material_guid_source = USERmax_exp_temperature = 361max_power = 75max_target_temperature = 350.0maximum_temperature = 350nominal_resistance = 23.0nozzle_size = 0.4pid_Kd = 40.0pid_Ke = 0.0pid_Kff = 0.57pid_Ki = 0.2pid_Ki_max = 100pid_Kp = 9.0pid_Kpcf = 0.06pid_functional_range = 25.0pre_tune_target_temperature = 0.0programming_state = serial_number = 14db96100000target_temperature = 0.0time_spend_hot = 85756tune_offset_temperature = 0.0voltage = 24.0x_offset = 0y_offset = 0z_height = 3.7404787726917803(Cmd) set pre_tune_target_temperature 20 (Cmd) Jun 29 15:43:20 ultimakersystem-ccbdd300003f python3.4: 15:43:20,352 INFO heatableHotend Going to enable hotend 0 to 20CJun 29 15:43:20 ultimakersystem-ccbdd300003f python3.So when I first boot my server on my rpi 4, I can reach the server from my desktop computer via the browser no problem. Although it's less than useful if you don't have a touch screen, if you like the roomier ribbon, you can use it with a mouse. This adds the Touch Mode button to the QAT which you can use to toggle Touch Mode off and on. #REPETIER SERVER TOUCHSCREEN MODE EXIT CODE#The console also has code completion in a lot of places, so you can type select and hit tab and get a list To check out touch mode, expand the Quick Access Toolbar menu and select Touch Mode. Or if you are in the console you can select the hotends and set the "pre_tune_target_temperature"
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |